Thursday, November 19, 2026

MrHonda adopts an orphan Unicorn-1980 CT110

 I’ve been looking for months to find a little small-bore bike that has a rear rack and can keep up 40 mph on the way back from my trips to the post office. The little S90 would only barely do 40 when maxed out in 2nd gear. I didn’t want to make a habit of that with the poor thing. A patina coated CB400F came along with the S90 deal and it had its own issues with over-sized tires, Keyster carb needles, brake caliper needing rebuild, new battery and rebuilt master cylinder and lately the clutch hub cushions are shrunken and the clutch is rattling. All this at under 12k miles. The bike appears to have been left under a tarp in someone’s back yard or maybe close to the ocean. There is LOTS of rust pitting, aluminum scale and general untidiness.


So, here on 10/07/2026, a 1980 CT110 ‘Trail 110” pops up less than 2 miles from the house. It was listed on Craigslist the night before and I traded messages with a guy who had listed it for his local friend. Only a few photos, text claiming that it was 100% complete, but one of the side shots clearly showed a missing chain guard. Finally, I was able to converse with the actual owner, just down the road and made an appointment to see it.




As usual, they are much worse looking in person than the photos convey in the ads. It did only have about 2200 miles on the speedo and the tires had been changed in 2018 with not much wear after that. The bike was usually kept in the desert and the split seat cover and general dirt and fading was a testament to the life it lead 46 years ago. The owner offered one of the old tiny pink, ‘pink slips” and some off-road registrations with the last one expiring in June. The bike hadn’t run in about 4-5 years, and the battery was totally dead. It was priced at $975 and the owner only came down $25 in negotiations. Still it seemed to have good bones, so we made the deal and I loaded it up in the Tacoma for the first stop at the local AAA for a title change.



They were not too busy when I arrived, still in the grips of some 100-degree temperatures that held sway for several weeks in CA. They offered me a cold bottle of water and within a few minutes, a young woman named Haley called me back to begin the paperwork. At first she couldn’t find the bike’s presence in the DMV system, but with more digging she discovered all the previous “off-road” stickers that DMV issues for bikes that are not going to be driven on the streets, even though it was obviously a street bike with turn signals and full lighting. So, what came to our attention was that the title was notated “OFF-ROAD” at the top of the little title. So, Haley could only charge me for the new title and the off-road fees, but NOT for a street bike title and tags. They said that only the DMV can change the title from “Off-Road” to a normal CA title for a street bike. RATS!


I was able to extract the ignition switch and observe the key code on the side of the switch body. These later switches have 5-6 numbers stamped on the sides, but only the last three digits are the key cold. An eBay key seller took the codes and will ship out a pair of nice, flat keys in the coming days. Back on eBay, I sifted through a bunch of chain guards for sale, ranging from $15 to $75. I put in an offer on a used one for $25 and they took the offer. Next, I will dug into the compression, valve adjustment, remove and clean the carburetor after the fuel tank is drained. It has the little auxiliary fuel tank clamped on the back rack section. It has a 1/3 fuel load inside as well.


Sadly, I had overlooked the fact that that the fork stops on the frame were sheared off, so the forks come around at almost 90 degrees. I’ll have to come up with a fix for that, as it causes the bike to keel over on the side stand. Read on for that little side story.

1979 was the last year of production for the CT90 Trail 90 (50.0 mm × 45.6 mm engine size), which was equipped with a centerstand, a left side rear brake lever/cable for the rear brake and the dual-range transmission option. For reasons unknown, Honda increased the engine size to 105cc (52.0 x 49.5mm bore/stroke), bumping up the bore and stroke slightly and then called it a CT110, but they left the dual- range transmission option and the centerstand OFF! This was met with an immediate outcry from the fans of the Trail 90 enthusiasts, so Honda reversed course and added the dual-range transmission back to the 1981 models. Plus they added the centerstand back under the motor, so you had two options for parking. The early CT110 models continued to use the tried and true points and condenser ignition system, brought over from the CT90s. By 1982 Honda added the new CDI ignition system to the models, finally letting the old points and condenser go bye-bye.


Looking at images and parts lists, the left side handlebar lever, used to activate the rear brake continues to be NLA on all CT110s. It was a handy feature when trying to hold a bike on a steep hill. If you are holding the bike upright with your feet, reaching for the rear brake pedal can upset your balance, plus you have the benefit of both wheel braking on soft ground. Apparently, that is no longer a consideration for Trail 110 enthusiasts. At least they reinstated the centerstand and the dual-range transmission functions in 1982!


So, on a rainy Saturday morning, I enlisted the services of my local muffler shop welder friend to repair the damaged steering stop on the frame. First, I had to remove the headlight, headlight case, speedo cable and then push all the spaghetti wiring out of the rear hole in the shell. I cleaned the area with brake cleaner to get the grease out of the joint. Then, I backed the bike up into the Tacoma bed backwards, so the welder could work on it at a good height, hopefully so I didn’t have to unload and load the bike up again. We discussed what needed to happen, found some chunks of steel and reduced it down to a small cube. Unfortunately, he only has a MIG welder, so the end result wasn’t as pretty as it would have been with a TIG welder. Anyway, the deed was done and I raced back home as the tropical storm system began to leak over San Diego County. Mission accomplished.


Then, there was the matter of a dead Yuasa battery that was about 1/3rd dry. I added a bit of acid and put it on the slow 6v charger for a few hours. Surprisingly, it bounced back to about 6.0v so I felt good about at least getting some spark out of the ignition. Little did I know that I was about to get a BIG lesson in the redesigned Honda ignition system for the CT110. You see, the ignition is not battery-powered and is not a CDI, either. I wasted quite a bit of time and effort to disassemble the ignition switch because I couldn’t get power to the black/white stripe wire that feeds the coil and points.


In the “old days” the battery fed the coil and points in a normal points and condenser ignition system which has been a staple of Honda 90cc singles, and all other models bigger than 65cc since the 1960’s. The ignition switch only has one click position… ON or OFF. What I was able to trace with a volt probe was that power was being switched from the RED to BLACK wires when the switch was ON, but there was a second set of contacts inside the switch which connected the Black white/strip wire to GREEN… ground. I thought that somehow the ignition switch contacts were corroded and not doing their job. The switches are not really designed to be disassembled and I was surprised to find a small ball bearing shoot out from the switch base and fly across the shop bench into oblivion I took the contact plate to my little 3” belt sander and ground the plate down to where all the contacts were flat and even with the plate surface.


Having lost the little 1/8” ball and not finding another one in all of my bits and pieces of electrical spares, I had to grind down a Phillips head screw and used it in place of the missing steel ball. It actually worked okay, but of course, there was no change in the switch function because it was WORKING NORMALLY! So, that left me to ponder just what was it that I was missing in this picture. Fortunately, members of the Facebook Honda CT90-110 forum spoke up and one informed me that the ignition system is NOT powered by the battery!


What happens is that there is an extra coil in the stator which generates the power to the ignition system, but only when the engine is turning. That makes testing the point timing a bit difficult, as there is no measurable voltage at the points in a static state. Finally, it all began to make sense to me. After I had reattached the headlight shell and speedo, then stuffed all the wired back inside, I looked for the black white/stripe wire connector with a different understanding. With the spark plug removed, I pushed the kickstarter over a few times with the plug grounded to the head and low and behold, I saw a SPARK! And the battery was still not installed at that moment.


Sadly, all of my unnecessary ignition switch disassembly came back to bite me when after it was reinstalled back into the frame, the back plate loosened up and lost connection with the sliding contacts, then it just flew apart when I tried to remove it from the ignition switch hole. Back to eBay and I found a NOS ignition switch for $40, plus shipping. That arrived quickly and it, of course, functions perfectly.


How clever that Honda designed a system like this, so that if you were out trail riding and the battery failed for some reason, the bike would keep running because of a self-powered ignition system. So, now I have added some new appreciation and some fresh knowledge that I never had before in my 60 years of wrangling and repairing vintage Honda motorcycles. You CAN teach an old dog new tricks!


While I was buying up replacement parts, I found a replacement seat cover and a NOS headlight rim for not too much money, so the overall condition is coming along. I did remove the exhaust system to access the fuel tank mounting hardware, so I could replace the fuel lines coming from the bottom of the tank. While I was “fixing stuff” I grabbed my MAPP gas torch and heated up the bent left side foot peg bracket. The bike leans over more than I care for, but the side stand bolt hole is probably worn out of round so there is slop in the joint, allowing for the extra lean angle.


Among the other improvements to the engine was the redesign of the cylinder head’s combustion chamber to allow for a D8ES long reach spark plug vs the old D8HA short reach plug. All of the valve train items, including the camshaft are all CT110 specific. On the other hand, most of the camchain tensioner pieces are all holdover CT90 parts of various series. The carburetor has the built in petcock function and fuel strainer, but the main jet size is only a #70. The 1982-84 used a #72 main jet. Conversely, the high-winding S90 used main jets in the #80-88 sizes. It seemed that surely the engine was designed for low-mid range power delivery vs the high-speed street bike power curves.


I fought the bike for several days about what appeared to be poor carburetion issues. The bike was hard to start, then backfired back through the carburetor! When it first arrived, I checked and loosened up the valve clearances, cleaned and lubricated the spark advancer, then I “eyeballed’ the ignition timing because there is no power to the points to do a standard timing check with a 12v test light. After having the carb apart for cleaning, then buying a carb kit for it, nothing seemed to cure the snapping back problem through the carburetor.


At a loss, I enlisted the help of some of the members of the CT90-110 Trail bike group on Facebook. There were a few laughable comments, but a couple of members mentioned checking the timing. I countered with “Did that” but in the back of my mind, I thought maybe it was worth re-visiting. So, I pulled out my VOM unit and set it on buzz so I could hear the points open and close while I turned the flywheel over. There are two screw-in plugs in the dyno cover to allow access to the timing marks and to turn the crankshaft over. The top one with the small hole makes it difficult to actually see the F and T marks without a flashlight. I disconnected the point wire connection just above the cylinder and tapped into the wire with the meter. As I turned the crankshaft back and forth, I discovered that my “eye ball” technique was about 10 degrees ADVANCED from the F mark alignment. This setting would explain why the engine would kick back when I tried to start it and also the backfire through the carb throat. Once the timing was reset again, the bike would fire up much more easily, idled down smoothly, and when I drove it around the block, it pulled in all 4 gears with relative authority for a 105cc engine in a bike that weight 200 lbs. Finally, the head-scratching mystery was solved, all due to my shortcut timing method.


Unfortunately, that was not the end of the sorrows with the bike. It became harder and harder to kickstart due to a slipping clutch, so it wound up on the bike work bench for an oil drain, clutch cover off and new fiber plates from eBay sellers. All the parts arrived quickly and I had to study up on the reassembly of the clutch pack. New clutch springs seemed to help the kickstarter function quite a bit.

All that was left was to repair the turn signals. These cheap plastic units have flimsey socket bases that don’t hold bulbs in very tightly. After taking a couple of them apart, I was able to assemble them enough to allow the function to return once again. Whew!

DMV DRAMA and TRAUMA

While working on the CT110 story about this bike that has caused me fits in more ways than one, I had to write out the following story add-on. I wanted to share the bizarre and frustrating DMV experience in getting this "street legal" CT110 licensed for the street again.

Back Story...

The bike showed up for sale just 2 miles away. With only 2600 miles on it, it should be functionally sound and an easy fix. Without going into all the mechanical issues, it was the DMV experience that caused the most upset. You see, the CT110, which was bought from the original owner, was tagged with "off road vehicle" on the title, because their intention was just to ride it out in the desert where they had a second home. When AAA tranferred the title to my name, they couldn't change the status to a normal title. It had to be done by the DMV. AAA charged me $115 to transfer it to my name, but then they gave me a new "off-road" sticker to put on top of the stack placed on the rear fender. So, I was already getting buried in fees for a cheap fixer upper Trail 110.

Next, once the new "off-road" title was received, I loaded the bike up and hauled it down to the DMV expecting to have it inspected and then released as a street bike. I did the digital "sign up on line" from home with an estimated 30 minute wait. The drive to DMV took about 15 minutes. I went to the vehicle inspection first, but no one was immediately available to check it over. I got a notification that my turn was coming up inside, so I drove out of the inspection aisle and ran inside to get a start on the paperwork. The woman heard the story and then said I had to get it inspected first!

So, back to the inspection lane where I was seen by what appeared to be the one person who was shuttling back and forth between the inspection and drive testing duties. He took the new title as a reference and then did a normal check. Thank goodness he did, as the new title had a typo in the serial number. So with a new inspection done, it was back inside where the woman told me that A. I had to pay the full $159 for a street plate and B I couldn't get credit for the money I had just paid for the "off road" sticker. So C, pay the $159 or choose $57 to get it into non-op status, however the bike now had "dual registration" status. It was legal to drive off-road, but not on the street. When the off-road renewal comes up in 11 months, I can then put it in non-op status and choose to put the bike back into normal street status again. I chose non-op for the street status, so someone else can tag it for the street once sold. At least the new title will hopefully not show "off road" status alone.

AHMC factory photo. 

Who knows what will happen when the new title comes in a few weeks. Sadly, this is the third bike I have bought that had title issues. Of the first two, one had no engine number on the title, which is required in California, and the other one had the same engine and frame numbers on the title. I had to run each one back to DMV for inspection corrections and eventually got new correct titles for them. These vintage bikes can be a PIA at times, especially with titles and registrations.

Bill Silver

www.vintagehonda.com

P.S. DMV gifted me with TWO CA titles for this ONE BIKE! One for the off-road mode and one that is just Non-Opted status. SOLD TODAY 11/19/2026


No comments:

Post a Comment